6 Tips for Maintaining Your Garage Door and Prolong Its Service Life

Many homeowners tend to neglect garage door maintenance as well as overlook any occurring issues in its functioning up until it stops working completely. It can turn out to be an expensive mistake, as, in the best-case scenario, you will have to replace some of the garage door parts with new ones or install a brand new garage door.

However, you can avoid those issues and undesirable expenses if you learn to maintain your garage door properly. It will not take much of your time but will significantly prolong its service life.

Below, you will find six garage door maintenance tips, ranging from lubricating the moving parts, inspecting the rollers, cables, and springs to cleaning the tracks, testing the door’s balance, and tightening the hardware, among other things. Read on and ensure your garage door’s proper operation.

Check Torsion Spring Tension

Torsion springs are located inside torsion shafts placed on both sides of your garage door’s header, which is why they are easy to inspect without taking them out from their brackets. To check torsion springs for tension, all you have to do is lift the door halfway and listen to whether they make any noise when going up or down (they shouldn’t).

However, if you hear a rattling or scraping noise when the door goes up or down, it means that the springs are loose or damaged and require replacement. To check whether they are loose, you should lift your garage door halfway and hold it in that position for at least a minute. If they make noise when going up or down, then they need to be tightened.

One of the most cost-effective solutions for maintaining or replacing torsion springs is to look for a broken garage door torsion spring repair replacement kit. It usually consists of new parts and includes all the necessary tools for installation and fixing your garage door.

Check Rollers and Cables

For smooth movement of your garage door, check rollers for any visible signs of damage, such as cracks or dents, as well as frays in the cables or springs connected to them. You should replace them if they are broken or damaged in any other way.

You can take rollers out from their brackets for inspection by loosening screws, holding them in place, and unplugging the coils from their brackets. Next, remove coil springs from their brackets by removing clips holding them in place and disconnecting them from their brackets using pliers or a screwdriver.

While checking rollers for damage, you can also lubricate them if necessary using spray lubricant or oil according to the model of your garage door opener system.

6 Tips for Maintaining Your Garage Door and Prolong Its Service Life

Inspect and Clean Your Tracks

The tracks are probably the most critical part of your garage door as they are responsible for the proper functioning of the door itself. Therefore, it is crucial for you to inspect and clean them regularly to prevent any malfunctions in their movement.

To inspect your garage door tracks, you should lift your garage door and look at both sides of its tracks while it is fully open. Ensure that there are no cracks or dents on them, as those will lead to a malfunction in your door’s operation. If you find any such issues, you should replace those parts immediately.

In addition to inspecting your tracks, you should also clean them from time to time to make them work more efficiently. Many products on the market can help you do that, including spray cleaners and degreasers. You can also use a toothbrush and a water hose to clean debris from small cracks in your tracks.

Lubricate Moving Parts

In addition to inspecting and cleaning your tracks, you should also lubricate moving parts of your garage door. The purpose of using lubricant is to reduce friction between parts of the door, reduce strain on them, and extend their service lives. Moreover, lubricating moving parts will make them work quieter without creating squeaks and rattles when operating.

You can either lubricate moving parts manually (according to the instructions from your owner’s manual) or use a spray lubricant on areas requiring lubrication, depending on the model of your door – pulleys, springs, rollers, pivot points, hinges, etc.

Check the Garage Door Balance

As a garage door is used regularly, it sags on one side or another. When you notice that your garage door doesn’t close correctly or goes off-track while going up or down, you should immediately check its balance. It won’t take much of your time and effort to do it yourself.

You will need to know the gauge of the cables and springs so that if you need to replace them with new ones, you will buy exactly the same size. Then, you will have to release the spring tension and remove the cables and springs. Once you are done with that, get a weight equal to the total weight of the removed components.

Raise the door halfway and put the weight at the bottom of the door. If the door doesn’t stay in place during the process, you will need to adjust its balance. In order to do that, you will have to loosen either the top or bottom cable by turning the screw at least three turns counterclockwise. Tighten the opposite cable in the same way. You should repeat this process until the door stays in place at the desired height.

After you are done with this process, you can reinstall all components and adjust their tension. After that, test your garage door to see whether it closes properly.

Check Other Parts and Tighten Hardware and Screws

The bearing holes are located between the track sections of a garage door and support its weight when it moves up or down. Therefore, you should inspect them from time to time in order to make sure that they are not damaged and are in good condition. Also, pay attention to nuts and bolts connecting sections of your track and tighten hardware to prevent any issues with the movement of your garage door.

If your garage door has hinges made of plastic or metal, it is crucial for you to inspect them once in a while as they tend to wear out over time, leading to a significantly reduced service life of your garage door. Therefore, inspect hinges for visible signs of damage such as cracks, chips, or dents and tighten screws holding them together with nuts so that they are not loose anymore in order to minimize the risk of any possible malfunctions.

In Conclusion

Learning how to maintain your garage door properly will allow you to avoid malfunctions in its operation and save you a lot of money in the long run. All that is required from you is to inspect your garage door’s parts regularly (without neglecting even the slightest damage), observe its movement, and take action immediately if needed.

Make sure to get in the habit of lubricating, cleaning, and tightening all the parts, and your garage door will reward you with extended service life.

 

Thank you for reading!

Click Here to Leave a Comment Below 0 comments